- QUERY SWITCH FOR MAC TABLE SNMP HOW TO
- QUERY SWITCH FOR MAC TABLE SNMP SERIAL
- QUERY SWITCH FOR MAC TABLE SNMP SERIES
Use the show config privileged command to display the current system configuration.
QUERY SWITCH FOR MAC TABLE SNMP HOW TO
The following example shows how to display CGMP statistics for VLAN 2: Console> show cgmp statistics 8ĬGMP enabled CGMP statistics for vlan 1: valid rx pkts received 48 invalid rx pkts received 0 valid cgmp joins received 23 valid cgmp leaves received 25 valid igmp leaves received 25 valid igmp queries received 22 igmp gs queries transmitted 25 igmp leaves transmitted 25 failures to add GDA to EARL 0 topology notifications received 0 152> (enable) Related Commands (Optional) VLAN number for which to display CGMP statistics. show cgmp statistics Syntax Description vlan_id Use the show cgmp statistics command to display Cisco Group Management Protocol (CGMP) statistical information. The following example shows how to display CDP information for a particular port:
QUERY SWITCH FOR MAC TABLE SNMP SERIAL
Hardware Version: 3.0 Model: WS-C1201 Serial #: 062000101ģ2K bytes of non-volatile configuration memory. WS-C1201 Software, Version DmpSW: 4.26 NmpSW: 4.26 The following example shows how to display detailed CDP information:Ĭonsole> (enable) show cdp neighbor 4 detail Port Device-ID Port-ID Platform Capability S - Switch, H - Host, I - IGMP, r - Repeater The following example shows how to display CDP information about neighboring systems:Ĭapability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge (Optional) Keyword used to show detailed information about neighboring Cisco products. (Optional) Number of the port for which CDP information is displayed. If no module number is specified, CDP information for the entire switch is displayed. (Optional) Number of the module for which CDP information is displayed. Keyword used to show CDP information for all Cisco products connected to the switch. Show cdp port ] Syntax Description neighbors Use the show cdp command to display Cisco Discovery Protocol (CDP) information. The following example shows how to display CAM aging time information: Use the show cam agingtime command to display CAM aging time information for all configured VLANs. VLAN Destination MAC Destination Ports or VCs The following example shows how to display dynamic CAM entries for VLAN 1: If a VLAN is not specified, all VLANs are displayed. Keyword used to display system CAM entries. Keyword used to display permanent CAM entries. Keyword used to display static CAM entries. Keyword used to display dynamic CAM entries. Show cam mac_addr Syntax Description dynamic Use the show cam command to display the content-addressable memory (CAM) table. Shows the default method for translating IPX 2 packets across various media.ĪPaRT=automated packet recognition/translation Indicates whether IP fragmentation is enabled or disabled. Indicates whether FDDICHECK is enabled or disabled. Indicates whether APaRT 1 is enabled or disabled. Table 6-1: show bridge Command Output Fields Field Table 6-1 describes the fields in the show bridge output. The following example shows how to display bridge information: This command has no arguments or keywords. Use the show bridge command to display bridge information.
The remaining lines of the display show mappings of IP addresses (or IP aliases) to Media Access Control (MAC) addresses. This value is set using the set arp agingtime command. "ARP Aging time" is the period of time after which an ARP entry is removed from the ARP table. The following example shows how to display the ARP table: (Optional) Keyword that forces the display to show only IP addresses, not IP aliases. Use the show arp command to display the Address Resolution Protocol (ARP) table. The following example shows how to display all aliases: If name is not specified, all defined aliases are displayed. (Optional) Name of the alias to be displayed. Use the show alias command to display a listing of defined command aliases. show commands are described in the " ATM show Commands" chapter show alias.General commands are described in the " General ATM Commands" chapter.set commands are described in the " Switch set Commands" chapter.clear commands are described in the " Switch clear Commands" chapter.General commands are described in the " General Switch Commands" chapter.Other commands are described elsewhere in this publication: For more information about using the switch CLI, refer to the " Switch Command-Line Interface" chapter. For a summary of the available switch CLI commands, refer to the " Switch Command Quick Reference" chapter.
QUERY SWITCH FOR MAC TABLE SNMP SERIES
This chapter describes the show commands used in the Catalyst 5000 series switch command-line interface (CLI).
0 kommentar(er)
